Lenovo 7D1J Reference Download Page 181

Page: 181 / 246

Table 4. Events organized by severity (continued)

Event ID

Message String

Severity

FQXSFPU0006K

A power segment mismatch has been detected for one or more
processors.

Error

FQXSFPU0007K

Processors have mismatched Internal DDR Frequency

Error

FQXSFPU0008K

A core speed mismatch has been detected for one or more
processors.

Error

FQXSFPU0009K

An external clock frequency mismatch has been detected for one or
more processors.

Error

FQXSFPU0010K

A cache size mismatch has been detected for one or more
processors.

Error

FQXSFPU0011K

A cache type mismatch has been detected for one or more
processors.

Error

FQXSFPU0012K

A cache associativity mismatch has been detected for one or more
processors.

Error

FQXSFPU0013K

A processor model mismatch has been detected for one or more
processors.

Error

FQXSFPU0014N

A processor family mismatch has been detected for one or more
processors.

Error

FQXSFPU0015K

A processor stepping mismatch has been detected for one or more
processors.

Error

FQXSFPU0016N

A processor within the system has failed the BIST.

Error

FQXSFPU0017G

A processor microcode update failed.

Error

FQXSFPU0018N

CATERR(IERR) has asserted on processor [arg1].

Error

FQXSFPU0019N

An uncorrectable error has been detected on processor [arg1].

Error

FQXSFPU0030N

A firmware fault has been detected in the UEFI image.

Error

FQXSFPU0031N

The number of POST attempts has reached the value configured in F1
setup.The system has booted with default UEFI settings. User
specified settings have been preserved and will be used on
subsequent boots unless modified before rebooting.

Error

FQXSFPU0034L

The TPM could not be initialized properly.

Error

FQXSFPU0035N

A 3-strike timeout has occurred on processor [arg1].

Error

FQXSFPU4056M

TPM card is changed, need install back the original TPM card which
shipped with the system.

Error

FQXSFSM0008M

Boot permission timeout detected.

Error

List of UEFI events

This section lists all messages that can be sent from UEFI.

•

FQXSFDD0001G: DRIVER HEALTH PROTOCOL: Missing Configuration. Requires Change Settings

From F1.

Severity: Warning

Chapter 4

UEFI events

177

Summary of Contents for 7D1J























































































































































































































































Search results

Summary of Contents for 7D1J

Reviews:

Related manuals for 7D1J

Brands by name

Popular brands

Lenovo 7D1J, Reference

Search results

Summary of Contents for 7D1J

Reviews:

Related manuals for 7D1J

Brands by name

Popular brands