Lenovo 7D1J Reference Download Page 20

Page: 20 / 246

2. If the event persists, ensure all populated compute nodes are completely power off, then reseat

SMM2 module. (Service technician only)

3. If the event persists, ensure all populated compute nodes are completely power off, then replace the

SMM2 module. (Service technician only)

4. If the event persists, please consult with technical service.

•

0201070C: SMM2 Brd 5V: Voltage sensor, warning event was asserted, reading value %V

(Threshold %V)

Asserted when voltage sensed on 5V power rail is higher than upper non-critical threshold.

Severity: Information
Alert Category: System - SMM2 system event
SNMP Trap ID: 33621772

User Action:

1. Virtual reset SMM2 via Web GUI or IPMI command.

2. If the event persists, ensure all populated compute nodes are completely power off, then reseat

SMM2 module. (Service technician only)

3. If the event persists, ensure all populated compute nodes are completely power off, then replace the

SMM2 module. (Service technician only)

4. If the event persists, please consult with technical service.

•

0201070D: SMM2 Brd 12V: Voltage sensor, warning event was asserted, reading value %V

(Threshold %V)

Asserted when voltage sensed on 12V power rail is higher than upper non-critical threshold.

Severity: Information
Alert Category: System - SMM2 system event
SNMP Trap ID: 33621773

User Action:

1. Virtual reset SMM2 via Web GUI or IPMI command.

2. If the event persists, ensure all populated compute nodes are completely power off, then reseat

SMM2 module. (Service technician only)

3. If the event persists, ensure all populated compute nodes are completely power off, then replace the

SMM2 module. (Service technician only)

4. If the event persists, please consult with technical service.

•

02010908: SMM2 Brd 1.15V: Voltage sensor, critical event was asserted, reading value %V

(Threshold %V)

Asserted when voltage sensed on 1.15V power rail is higher than high critical threshold.

Severity: Error
Alert Category: System - SMM2 system event
SNMP Trap ID: 33622280

User Action:

1. Virtual reset SMM2 via Web GUI or IPMI command.

2. If the event persists, ensure all populated compute nodes are completely power off, then reseat

SMM2 module. (Service technician only)

3. If the event persists, ensure all populated compute nodes are completely power off, then replace the

SMM2 module. (Service technician only)

4. If the event persists, please consult with technical service.

ThinkSystem DA240 Enclosure and ThinkSystem SD630 V2 Compute Node Messages and Codes Reference

Summary of Contents for 7D1J























































































































































































































































Search results

Summary of Contents for 7D1J

Reviews:

Related manuals for 7D1J

Brands by name

Popular brands

Lenovo 7D1J, Reference

Search results

Summary of Contents for 7D1J

Reviews:

Related manuals for 7D1J

Brands by name

Popular brands