Lenovo 7D1J Reference Download Page 143 | Manualshive

Page: 143 / 246

background image

1. Check the Support Portal (http://support.lenovo.com/) for service bulletins and TECH tips and

firmware update related to your drive.

2. Check for any other RAID-related error.

3. Replace the drive.

•

FQXSPSD0003G: Failure Predicted on drive [arg1] in the enclosure/chassis (MTM-SN: [arg2]).

This message is for the use case when an implementation has detected an Array Failure is Predicted.

Severity: Warning
Serviceable: Yes
Automatically notify Support: Yes
Alert Category: System - Predicted Failure
SNMP Trap ID: 27
CIM Prefix: PLAT CIM ID: 0168

User Action:

Replace drive 0 at the next maintenance period.

•

FQXSPSD0003I: Hot Spare enabled for [ComputerSystemElementName].

This message is for the use case when an implementation has detected a Hot Spare has been Enabled.

Severity: Info
Serviceable: No
Automatically notify Support: No
Alert Category: System - Other
SNMP Trap ID:
CIM Prefix: PLAT CIM ID: 0170

User Action:

Information only; no action is required

•

FQXSPSD0005I: Hot Spare enabled for drive [arg1] in the enclosure/chassis (MTM-SN: [arg2]).

This message is for the use case when an implementation has detected a Hot Spare has been Enabled.

Severity: Info
Serviceable: No
Automatically notify Support: No
Alert Category: System - Other
SNMP Trap ID:
CIM Prefix: PLAT CIM ID: 0170

User Action:

Information only; no action is required

•

FQXSPSD0005L: Array [ComputerSystemElementName] is in critical condition.

This message is for the use case when an implementation has detected that an Array is Critical.

Severity: Error
Serviceable: Yes
Automatically notify Support: No
Alert Category: Critical - Hard Disk drive
SNMP Trap ID: 5
CIM Prefix: PLAT CIM ID: 0174

User Action:

.

XClarity Controller events

139

«
...
141
142
143
144
145
...
»

Summary of Contents for 7D1J























































































































































































































































Reviews:

No comments

Related manuals for 7D1J

Brand: Aastra Pages: 502

Brand: Atop Pages: 2

Brand: IBM Pages: 140

BladeCenter JS20

Brand: IBM Pages: 132

STRATOS S400-X44E

Brand: Quanta Computer Pages: 251

Brand: LevelOne Pages: 88

Brand: Hamlet Pages: 76

2500 - Color LaserJet Laser Printer

Brand: HP Pages: 24

Brand: HP Pages: 26

4650 - Color LaserJet Laser Printer

Brand: HP Pages: 2

615N - JetDirect Print Server

Brand: HP Pages: 56

4550 - Color LaserJet Laser Printer

Brand: HP Pages: 32

600N - JetDirect Print Server

Brand: HP Pages: 44

170X - JetDirect Print Server

Brand: HP Pages: 30

170X - JetDirect Print Server

Brand: HP Pages: 80

Brand: HP Pages: 116

300X - JetDirect Print Server

Brand: HP Pages: 102

Brand: HP Pages: 194

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands