Lenovo 7D1J Reference Download Page 180 | Manualshive

Page: 180 / 246

background image

Table 4. Events organized by severity (continued)

Event ID

Message String

Severity

FQXSFIO0022J

PCIe Link Width has degraded from [arg1] to [arg2] in PCIe slot [arg3].

Error

FQXSFIO0023J

PCIe Link Speed has degraded from [arg1] to [arg2] in PCIe slot
[arg3].

Error

FQXSFIO0031M

An Uncorrectable PCIe Error has Occurred at Bus [arg1] Device [arg2]
Function [arg3]. The Vendor ID for the device is [arg4] and the Device
ID is [arg5]. The physical bay number is [arg6].

Error

FQXSFMA0001M

DIMM [arg1] has been disabled due to an error detected during POST.
[arg2]

Error

FQXSFMA0002M

An uncorrectable memory error has been detected on DIMM [arg1] at
address [arg2]. [arg3]

Error

FQXSFMA0003K

A memory mismatch has been detected. Please verify that the
memory configuration is valid. [arg1]

Error

FQXSFMA0004N

No system memory has been detected. [arg1]

Error

FQXSFMA0005N

Memory is present within the system but could not be configured.
Please verify that the memory configuration is valid. [arg1]

Error

FQXSFMA0008M

DIMM [arg1] has failed the POST memory test. [arg2]

Error

FQXSFMA0009K

Invalid memory configuration for Mirror Mode. Please correct memory
configuration. [arg1]

Error

FQXSFMA0010K

Invalid memory configuration for Sparing Mode. Please correct
memory configuration. [arg1]

Error

FQXSFMA0023M

Error has occurred in NVDIMM flash. NVDIMM backup/restore may
not operate correctly. [arg1]

Error

FQXSFMA0024M

Error has occurred in NVDIMM Supercap. NVDIMM backup/restore
may not operate correctly. [arg1]

Error

FQXSFMA0025M

NVDIMM Supercap has been disconnected. NVDIMM will lose its
backup ability until this is corrected. [arg1]

Error

FQXSFMA0027K

Invalid memory configuration (Unsupported DIMM Population)
detected. Please verify memory configuration is valid.[arg1]

Error

FQXSFMA0028K

Memory Capacity exceeds CPU limit. [arg1]

Error

FQXSFMA0042K

Intel Optane PMEM is not supported by processor of this system.

Error

FQXSFMA0046M

DIMM [arg1] is disabled because it is Intel Optane PMEM that is not
supported on current platform

Error

FQXSFPU0001N

An unsupported processor has been detected.

Error

FQXSFPU0002N

An invalid processor type has been detected.

Error

FQXSFPU0003K

A processor mismatch has been detected between one or more
processors in the system.

Error

FQXSFPU0004K

A discrepancy has been detected in the number of cores reported by
one or more processors within the system.

Error

FQXSFPU0005K

A mismatch between the maximum allowed UPI link speed has been
detected for one or more processors.

Error

176

ThinkSystem DA240 Enclosure and ThinkSystem SD630 V2 Compute Node Messages and Codes Reference

«
...
178
179
180
181
182
...
»

Summary of Contents for 7D1J























































































































































































































































Reviews:

No comments

Related manuals for 7D1J

Brand: IBM Pages: 908

ProLiant DL180 Gen10

Brand: HPE Pages: 10

AMD Opteron LS20 Type 8850

Brand: IBM Pages: 68

HS21 XM BLADECENTER - L5408 FOR SPEC CPU2006

Brand: IBM Pages: 1

Brand: Patton electronics Pages: 16

LaCinema PlayHD

Brand: LaCie Pages: 2

SuperServer 5013G-M

Brand: Supero Pages: 104

PRIMERGY RX2520 M4

Brand: Fujitsu Pages: 92

Primergy RX200 S4

Brand: Fujitsu Pages: 127

PRIMERGY RX200 S3

Brand: Fujitsu Pages: 100

PRIMERGY RX200 S6

Brand: Fujitsu Pages: 126

PRIMERGY RX2510 M2

Brand: Fujitsu Pages: 74

PRIMERGY RX200 S5

Brand: Fujitsu Pages: 72

PRIMERGY RX2530 M4

Brand: Fujitsu Pages: 88

PRIMERGY RX2450 M1

Brand: Fujitsu Pages: 246

PRIMERGY RX2520 M5

Brand: Fujitsu Pages: 98

PRIMERGY RX1330 M4

Brand: Fujitsu Pages: 106

PRIMERGY RX200 S7

Brand: Fujitsu Pages: 86

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands