Larsen & Toubro C*2000 Series User Manual Download Page 15

Page: 15 / 183

Chapter 2 INSTALLATION & WIRING

2-1

Cx2000 AC Drive

2 INSTALLATION & WIRING

2.1 Installation precautions



Handle the inverter with care to prevent damage to the plastic components. Do not hold the inverter by the

front cover. It may fall off.



Install the inverter in a place where it is immune to vibration or extrusion under allowable temperature (-

10 C~ 50 C)



The installation environment of inverter will influence its service life directly, so the inverter shall be used in a

condition with standard specification



The inverter will be very hot during operation. Install it on a non-combustible surface, far away from hot

sources and inflammables.



Mount the inverter on a flat, vertical and level surface. Inverter orientation must be vertical. Also leave

sufficient clearances around the inverter.



Protect from moisture and direct sunlight.

10cm

3cm

10cm

3cm

2mm

10cm

3cm

Caution

Summary of Contents for C*2000 Series
























































































































































































Search results

Summary of Contents for C*2000 Series

Reviews:

Brands by name

Popular brands

Larsen & Toubro C*2000 Series, User Manual

Search results

Summary of Contents for C*2000 Series

Reviews:

Brands by name

Popular brands