Intel Embedded Intel486 Hardware Reference Manual Download Page 262 | Manualshive

Page: 262 / 334

background image

EMBEDDED Intel486™ PROCESSOR HARDWARE REFERENCE MANUAL

8-34

translation necessary for the DMA transfer between the memory (ISA or main memory) and the
ISA bus I/O. ISA-compatible DMA timing is supported. The DMA controller also features re-
fresh address generation and auto-initialization following a DMA termination.

Note that a DMA device (I/O device) is always on the ISA bus, but the memory referenced is lo-
cated on either an ISA bus device or in main memory. When the ISA bridge is running a DMA
cycle, it drives the MEMR# or MEMW# strobes, if the address is less than 16 Mbytes (000000-
FFFFFFh). The ISA bridge always generates ISA-compatible DMA memory cycles. The
SMEMR# and SMEMW# are generated if the address is less than 1 Mbyte (0000000-
00FFFFFh). To avoid aliasing problems when the address is greater than 16 Mbytes (1000000-
7FFFFFFh), the MEMR# or MEMW# strobe is not generated.

The channels can be programmed for any of four transfer modes: single, block, demand, or cas-
cade. Each of the three active transfer modes (single, block, and demand), can perform three dif-
ferent types of transfers (read, write, or verify). Note that memory-to-memory transfers are not
supported by the ISA bridge. The DMA supports fixed and rotating channel priorities.

Figure 8-8. Internal DMA Controller

8.4.6.1

DMA Status and Control Interface

DMA Request lines, DREQ3–DREQ0, DREQ7–DREQ5, are used to request DMA service from
the ISA bridge’s DMA controller or for a 16-bit master to gain control of the ISA expansion bus.
The active level (high or low) is programmed via the DMA Command register. All inactive to
active edges of DREQ are assumed to be asynchronous. The request must remain active until the
appropriate DACKx# signal is asserted.

DMA Acknowledge output lines, DACK3#–DACK0#, DACK7#–DACK5#, indicate that a re-
quest for DMA service has been granted by the ISA bridge or that a 16-bit master has been grant-
ed the bus. The active level (high or low) is programmed via the DMA Command register. These
signals are deasserted after a hard reset.

Terminal Count, TC, is asserted by the ISA bridge to DMA slaves as a terminal count indicator.
This signal is deasserted after a hard reset.

Refresh, REFRESH#, is an output when asserted indicates when a refresh cycle is in progress. As
an output, this signal is driven directly onto the ISA bus. This signal is an output only when the
ISA bridge DMA refresh controller is a master on the bus responding to an internally generated
request for refresh. As an input, REFRESH# is driven by 16-bit ISA bus masters to initiate refresh
cycles. This signal is 3-stated after a hard reset

.

Channel 4

Channel 3

Channel 0

Channel 1

Channel 2

Channel 5

Channel 7

Channel 6

DMA-1

DMA-2

«
...
260
261
262
263
264
...
»

Summary of Contents for Embedded Intel486















































































































































































































































































































































Reviews:

No comments

Related manuals for Embedded Intel486

FrameSaver 9120

Brand: Paradyne Pages: 2

Brand: CSS Pages: 2

XM24 Expansion Module

Brand: Avaya Pages: 5

RCO-3000 Series

Brand: C&T Solution Pages: 96

Brand: Teletronics International Pages: 57

Brand: ZKTeco Pages: 68

Brand: Lanner Pages: 141

Brand: Dantel Pages: 22

Brand: Digisol Pages: 73

ULTRIX-FM-NS-1RU

Brand: Ross Pages: 5

Brand: ADLINK Technology Pages: 86

Brand: ADC Pages: 29

Brand: R3 Pages: 48

Brand: Promax Pages: 32

Brand: Reach Pages: 21

Brand: VALKYRIE Pages: 26

OFFICEBRIDGE ONLINE

Brand: Muratec Pages: 220

Wind Top AE2712 Series

Brand: MSI Pages: 91

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands