Intel Embedded Intel486 Hardware Reference Manual Download Page 211 | Manualshive

Page: 211 / 334

background image

7-39

PERIPHERAL SUBSYSTEM

•

Industry-Standard Network Support

— IEEE 802.3 (Ethernet, Ethernet Twisted Pair, Cheapernet, StarLAN, etc.)

— IBM PC Network (baseband and broadband)

— Proprietary CSMA/CD networks up to 20 Mbits/second

— HDLC frame delimiting

•

Compatible Intel486 Processor Interface

— Optimized interface to the Intel486 processor bus

— Shared Intel486 processor bus signals and memory timing

— Support for Intel486 processor byte ordering

•

Architectural Features

— On-chip DMA

— Bus Throttle

— 128-byte receive FIFO, 64-byte transmit FIFO

— On-chip memory management

— Network management and diagnostics

— 82586 software-compatible mode

•

Performance Features

— 9.6 msec interframe spacing for back-to-back frame transmission and reception

— 80/106 Mbytes/second bus transfer rate (burst) at 25/33 MHz

— 50/66 Mbytes/second bus transfer rate (non-burst) at 25/33 MHz

Figure 7-21

is a block diagram of the 82596 coprocessor. A serial subsystem interfaces to the

physical-layer device for the network. This subsystem performs CSMA/CD media access-control
and channel-interface functions. It supports the full set of IEEE 802.3 and other industry-standard
and proprietary network functions. A parallel subsystem interfaces to the Intel486 processor. This
subsystem contains a data interface unit, a bus interface unit, a 4-channel DMA unit, and a micro-
machine command processor. A FIFO subsystem connects the serial and parallel subsystems, al-
lowing them to run asynchronously to one another through a 128-byte receive FIFO and a 64-byte
transmit FIFO.

«
...
209
210
211
212
213
...
»

Summary of Contents for Embedded Intel486















































































































































































































































































































































Reviews:

No comments

Related manuals for Embedded Intel486

PCMCIA WIRELESS ASAPTER DWL-650

Brand: D-Link Pages: 5

PowerLine DHP-W611AV

Brand: D-Link Pages: 78

InterReach Fusion ADCP-77-044

Brand: TE Connectivity Pages: 236

Brand: CSS Pages: 2

Brand: Buffalo Pages: 2

PBE-5AC-300-ISO

Brand: Ubiquiti Pages: 28

Brand: Valcom Pages: 4

Brand: IBASE Technology Pages: 39

PCM-4141 Series

Brand: Advantech Pages: 96

PCard-E 021L-D5 Series

Brand: ORiNG Pages: 2

Brand: Rolls Pages: 1

DVI-Vision-IP-Fiber

Brand: G&D Pages: 240

SmartRack SR42UBEXPKD

Brand: Tripp Lite Pages: 8

Threat Analysis Reporter TAR

Brand: 8e6 Technologies Pages: 76

Symphonique Strings SRX-04

Brand: Roland Pages: 12

Brand: Jatontec Pages: 13

Brand: MSI Pages: 90

PayLink-IP/Dial

Brand: Lava Pages: 16

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands