Hyundai Body Builder 2015 Manual Download Page 219

Page: 219 / 284

INTRODUCTION

PRELIMINAR STUDIES AND CONSIDERATIONS

MAINTENANCE AND DAMAGE PREVENTION

WORK ON BASIC VEHICLE

MOUNTING AND CONSTRUCTION

POWER TAKE-OFF

ELECTRIC AND ELECTRONIC SYSTEMS

APPENDIX

V1.0, February 2015

Body Builder Manual Part II, Specific Book LCV

219

- All wires must be securely fixed and protected from sharp edges. Always use

grommets or other wear protection when wiring wires through metallic ele

ments. This will help to prevent short circuits caused by friction damage.

Fig. 7-159 LCV_SPBGC72_001 Different kinds of wiring protection

- It is recommended that clearance should be left between moving or vibrating

parts.

- Wires should never pass along brake pipes, fuel pipes or grease pipes. They

must not interfere with the movement of flexible tubes.

- The new wire routing should never pass through areas where it may be

assumed that it damage can occur due to mud, accumulation of snow, freezing,

or flying stones.

- Wires should be placed more than 200 mm away from exhaust system elements

such as tail pipes and mufflers. Otherwise, they should be protected by heat
insulators.

- When wiring inside the engine compartment, wires should pass directly through

the same route as the chassis harnesses already installed in this area. They
must be protected by heat insulators if necessary.

- The wires should be positioned at least to 50 mm from containers of chemical

agents, such as batteries.

- The wires must be long enough to ensure they are not subjected to tension.
- The distance between two consecutive fixations of wires should not exceed

300 mm.

- When installing additional equipment in the vehicle, it must be connected to a

vehicle earth point. See chapter 7.3.4 "Earth wire".

- The original installation should be restored after any interventions on the orig

inal wire route.

Steel plate

Clip

Wire

Protection

Summary of Contents for Body Builder 2015





























































































































































































































































































Search results

Summary of Contents for Body Builder 2015

Reviews:

Related manuals for Body Builder 2015

Brands by name

Popular brands

Hyundai Body Builder 2015, Manual

Search results

Summary of Contents for Body Builder 2015

Reviews:

Related manuals for Body Builder 2015

Brands by name

Popular brands