manualshive.com logo in svg

Honda CBF600N, Service Manual, Page: 65 / 620

Share
Download
Honda CBF600N Service Manual Download Page 65

FRAME/BODY PANELS/EXHAUST SYSTEM

2-11

MUFFLER

REMOVAL/INSTALLATION

Loosen the muffler band bolt.

Remove the muffler mounting nut, bolt, washer and
collar.
Remove the muffler and gasket.

Installation is in the reverse order of removal.

Tighten the muffler mounting nut to the specified
torque.

Tighten the muffler band bolt to the specified
torque.

EXHAUST PIPE

REMOVAL

Remove the muffler (page 2-11).
Remove the right side cover (page 2-5).

Disconnect the O

2

 sensor 4P (Black) connector.

Remove the exhaust pipe joint nuts.
Remove the exhaust pipe mounting nut, washer
and bolt.
Remove the exhaust pipe and gaskets.

Always replace the

gasket with a new

one.

TORQUE: 22 N·m (2.2 kgf·m, 16 lbf·ft)

TORQUE: 22 N·m (2.2 kgf·m, 16 lbf·ft)

BAND BOLT

MUFFLER

WASHER

MOUNTING 
BOLT

COLLAR

GASKET

NUT

4P (Black) CONNECTOR

MOUNTING BOLT

EXHAUST PIPE

GASKETS

JOINT NUTS

WASHER

NUT

Manuals by Motomatrix / www.motomatrix.co.uk / The Solution For Lost Motorcycle Coded Keys.

email: [email protected]

Summary of Contents for CBF600N













































































































































































































































































































































































































































































































































































































































Reviews:

No comments