Honda CBF600N Service Manual Download Page 234

Page: 234 / 620

COOLING SYSTEM

6-16

Connect the lower radiator hose and tighten the
hose band screw (page 6-22).

Connect the upper radiator hose and tighten the
hose band screw (page 6-22).

Route the horn wire through the guide of fan motor
shroud.

Connect the fan motor 2P (Black) connector.

Lower the fuel tank and install the front mounting
bolts (page 3-5).
Fill the system with recommended coolant (page 6-
6).

LOWER RADIATOR HOSE

BAND SCREW

UPPER RADIATOR HOSE

HORN WIRE

GUIDES

2P (Black) CONNECTOR

Manuals by Motomatrix / www.motomatrix.co.uk / The Solution For Lost Motorcycle Coded Keys.

email: [email protected]

Summary of Contents for CBF600N













































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for CBF600N

Reviews:

Honda CBF600N, Service Manual, Page: 234 / 620

Search results

Summary of Contents for CBF600N

Reviews: