Honda CBF600N Service Manual Download Page 396

Page: 396 / 620

FRONT WHEEL/SUSPENSION/STEERING

13-28

Apply fork fluid to the new oil seal lip.

Install the slider bushing, back-up ring and new oil
seal.

Install the oil lock piece onto the fork tube end.

Apply fork fluid to the fork tube bushing and slider
bushing, then install the fork tube into the fork
slider.

Drive the oil seal in using the special tools.

Install the stopper ring into the fork slider groove
securely.

Install the oil seal

with its marked

side facing up.

SLIDER BUSHING

BACK-UP RING

OIL SEAL

OIL LOCK PIECE

FORK SLIDER

TOOLS:
Fork seal driver weight

07947-KA50100

Oil seal driver attachment

07947-KF00100

DRIVER WEIGHT

ATTACHMENT

OIL SEAL

SLIDER BUSHING

BACK-UP RING

STOPPER RING

Manuals by Motomatrix / www.motomatrix.co.uk / The Solution For Lost Motorcycle Coded Keys.

email: [email protected]

Summary of Contents for CBF600N













































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for CBF600N

Reviews:

Honda CBF600N, Service Manual, Page: 396 / 620

Search results

Summary of Contents for CBF600N

Reviews: