manualshive.com logo in svg

Honda CBF600N, Service Manual, Page: 503 / 620

Share
Download
Honda CBF600N Service Manual Download Page 503

ANTI–LOCK BRAKE SYSTEM (ABS; CBF600SA/NA)

16-21

ABS INDICATOR CIRCUIT
TROUBLESHOOTING

ABS INDICATOR DOES NOT COME ON (when the
ignition switch turned to "ON")

1. Combination

Meter

Power/Ground

Line

Inspection

Check the combination meter power and ground
lines (page 20-21).

Are the wires normal?

YES

–

GO TO STEP 2.

NO

–

Open circuit in related wires.

2. Indicator Operation Inspection

Remove the seat (page 2-4).

Pull the lock lever up and disconnect the ABS
modulator 25P connector.
Turn the ignition switch to "ON" and check the
ABS indicator.

Does the indicator come on?

YES

–

Faulty ABS modulator.

NO

–

GO TO STEP 3.

3. Indicator Signal Line Short Circuit Inspection

CBF600SA:
Remove the front center cowl (page 2-10).
Remove the dust cover.
CBF600NA:
Remove the headlight unit (page 20-7)

With the connector connected, check for conti-
nuity between the Red/black wire terminal of the
harness side connector and ground.

Is there continuity?

YES

–

Short circuit in Red/black wire between
the combination meter and ABS modu-
lator.

NO

–

Faulty combination meter.

25P CONNECTOR

LOCK LEVER

CONNECTION: Red/black – Ground

16P (Black) 
CONNECTOR

DUST COVER

CBF600SA:

9P (Black) 
CONNECTOR

CBF600NA:

16P (Black) 
CONNECTOR

9P (Black) 
CONNECTOR

Red/black

Manuals by Motomatrix / www.motomatrix.co.uk / The Solution For Lost Motorcycle Coded Keys.

email: [email protected]

Summary of Contents for CBF600N













































































































































































































































































































































































































































































































































































































































Reviews:

No comments