Honda CBF600N Service Manual Download Page 364

Page: 364 / 620

CRANKSHAFT/PISTON/CYLINDER

12-16

Measure the piston pin bore.

Measure the O.D. of the piston pin.

Calculate the piston-to-piston pin clearance.

Measure the diameter of the piston at 6 mm (0.2 in)
from the bottom and 90 degrees to the piston pin
hole.

CONNECTING ROD INSPECTION

Measure the connecting rod small end I.D.

Calculate the connecting rod-to-piston pin clear-
ance.

SERVICE LIMIT: 16.02 mm (0.631 in)

SERVICE LIMIT: 15.98 mm (0.629 in)

SERVICE LIMIT: 0.04 mm (0.002 in)

SERVICE LIMIT: 66.90 mm (2.634 in)

6 mm (0.2 in)

SERVICE LIMIT: 16.05 mm (0.632 in)

SERVICE LIMIT: 0.07 mm (0.003 in)

Manuals by Motomatrix / www.motomatrix.co.uk / The Solution For Lost Motorcycle Coded Keys.

email: [email protected]

Summary of Contents for CBF600N













































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for CBF600N

Reviews:

Honda CBF600N, Service Manual, Page: 364 / 620

Search results

Summary of Contents for CBF600N

Reviews: