Honda CBF600N Service Manual Download Page 564

Page: 564 / 620

LIGHTS/METERS/SWITCHES

20-16

Remove the wire band.

Remove the handlebar (page 13-8).

Remove the stem nut.
Loosen the pinch bolt.

Remove the top bridge and combination meter
assembly.

DISASSEMBLY

Remove the mounting bolts and the top bridge from
the combination meter.

Remove the screws and lower cover.

WIRE BAND

COMBINATION METER

PINCH BOLTS

STEM NUT

TOP BRIDGE

BOLTS

LOWER COVER

SCREWS

Manuals by Motomatrix / www.motomatrix.co.uk / The Solution For Lost Motorcycle Coded Keys.

email: [email protected]

Summary of Contents for CBF600N













































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for CBF600N

Reviews:

Honda CBF600N, Service Manual, Page: 564 / 620

Search results

Summary of Contents for CBF600N

Reviews: