Honda CBF600N Service Manual Download Page 565

Page: 565 / 620

LIGHTS/METERS/SWITCHES

20-17

Remove the screws and combination meter front
cover.

Remove the meter screws.
Remove the bulb sockets.
Remove the screw, clamp and combination meter
sub-harness.

Remove the speedometer, tachometer and indicator
plate.

ASSEMBLY

Install the speedometer, tachometer and indicator
plate to the combination meter case.

SCREWS

FRONT COVER

SCREWS

SCREW/CLAMP

BULB SOCKETS

SUB-HARNESS

SPEEDOMETER

TACHOMETER

INDICATOR PLATE

SPEEDOMETER

TACHOMETER

INDICATOR PLATE

Manuals by Motomatrix / www.motomatrix.co.uk / The Solution For Lost Motorcycle Coded Keys.

email: [email protected]

Summary of Contents for CBF600N













































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for CBF600N

Reviews:

Honda CBF600N, Service Manual, Page: 565 / 620

Search results

Summary of Contents for CBF600N

Reviews: