Home
/
Honda
/
CBF600N
/
Service Manual

Honda CBF600N, Service Manual, Page: 386 / 620

Share

Page: 386 / 620

Honda CBF600N Service Manual Download Page 386

FRONT WHEEL/SUSPENSION/STEERING

13-18

To balance the wheel, install wheel weights on the
highest side of the rim, the side opposite the chalk
marks. Add just enough weight so the wheel will no
longer stop in the same position when it is spun. Do
not add more than 60 grams to the wheel.

This model is equipped with a new shape wheel
weight made of zinc spelter. This wheel weight is
incompatible with the conventional one in case of
installation to the wheel.

DISASSEMBLY

Remove the bolts and pulser ring.

Remove the bolts and brake discs.
Remove the dust seals.

Install the bearing remover head into the bearing.
From the opposite side, install the bearing remover
shaft and drive the bearing out of the wheel hub.
Remove the distance collar and drive out the other
bearing.

BALANCE WEIGHT

CBF600SA/NA only

BOLTS

PULSER RING

BRAKE DISC

DUST SEAL

BOLTS

TOOLS:
Bearing remover head, 20 mm 07746-0050600
Bearing remover shaft

07GGD-0010100 or
07746-0050100

REMOVER HEAD

REMOVER SHAFT

Manuals by Motomatrix / www.motomatrix.co.uk / The Solution For Lost Motorcycle Coded Keys.

email: [email protected]

«
...
384
385
386
387
388
...
»

Summary of Contents for CBF600N













































































































































































































































































































































































































































































































































































































































Reviews:

No comments