Honda CBF600N Service Manual Download Page 568

Page: 568 / 620

LIGHTS/METERS/SWITCHES

20-20

Connect the ignition switch 2P (Brown) connector.

Connect the immobilizer receiver 4P (Natural) con-
nector.

Route the wires

properly (page 1-

24).

Connect the combination meter 9P (Natural) and 9P
(Black) connectors.

Install the headlight unit (page 20-7).

2P (Brown) CONNECTOR

4P (Natural) CONNECTOR

9P (Black) CONNECTOR

9P (Natural) CONNECTOR

Manuals by Motomatrix / www.motomatrix.co.uk / The Solution For Lost Motorcycle Coded Keys.

email: [email protected]

Summary of Contents for CBF600N













































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for CBF600N

Reviews:

Honda CBF600N, Service Manual, Page: 568 / 620

Search results

Summary of Contents for CBF600N

Reviews: