Honda CBF600N Service Manual Download Page 147

Page: 147 / 620

FUEL SYSTEM (PGM-FI)

5-33

2. O

Sensor Heater Resistance Inspection

Turn the ignition switch OFF.

Disconnect the O

sensor 4P (Black) connector

and measure the resistance at the O

sensor con-

nector terminals of the sensor side.

Is the resistance within 10 – 40

Ω

(20

C/68

F)?

YES

–

GO TO STEP 3.

–

Faulty O

sensor

3. O

Sensor Heater Power Input Line Inspection

Turn the ignition switch ON and engine stop
switch " ".
Measure the voltage between O

sensor 4P

(Black) connector of the wire harness side and
ground.

Is there battery voltage?

YES

–

GO TO STEP 4.

–

Open circuit in the Black/white wire

4. O

Sensor Heater Open Circuit Inspection

Turn the ignition switch OFF.

Disconnect the ECM 33P (Light gray) connector.
Check the continuity between the ECM 33P
(Light gray) connector and O

sensor 4P (Black)

connector of the wire harness side.

Is there continuity?

YES

–

GO TO STEP 5.

–

Open circuit in Black/green wire

5. O

Sensor Heater Short Circuit Inspection 2

Connect the ECM 33P (Light gray) connector.

Check for continuity between the O

sensor

heater 4P (Black) connector of the wire harness
side and ground.

Is there continuity?

YES

–

Short circuit in Black/green wire

–

Replace the ECM with a known good
one, and recheck; refer to Key Registra-
tion Procedures (page 21-6)

CONNECTION: White – White

4P (Black) CONNECTOR
(Sensor side/female terminals)

White

CONNECTION: Black/white (+) – Ground (–)

Black/white

4P (Black) CONNECTOR
(Wire side/male terminals)

CONNECTION: B2 – Black/green

TOOL:
Test probe

07ZAJ-RDJA110

33P (Light gray)
CONNECTOR (Wire
side/female terminals)

B2
TERMINAL

4P (Black)
CONNECTOR (Wire
side/male terminals)

Black/
green

CONNECTION: Black/green – Ground

Black/green

4P (Black) CONNECTOR
(Wire side/male terminals)

Manuals by Motomatrix / www.motomatrix.co.uk / The Solution For Lost Motorcycle Coded Keys.

email: [email protected]

Summary of Contents for CBF600N













































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for CBF600N

Reviews:

Honda CBF600N, Service Manual, Page: 147 / 620

Search results

Summary of Contents for CBF600N

Reviews: