Honda CBF600N Service Manual Download Page 177

Page: 177 / 620

FUEL SYSTEM (PGM-FI)

5-63

Disconnect the ECM 33P (Black and Light gray) con-
nectors from the ECM.

Disconnect the CKP sensor 2P (Red) connector.

Release the IDC solenoid valve vacuum hose from
the guide of air cleaner housing.

Disconnect the crankcase breather hose from the air
cleaner housing.

Disconnect the #1/#4 ignition coil connectors.

ECM

33P (Black) CONNECTOR

33P (Light gray) CONNECTOR

2P (Red) CONNECTOR

GUIDE

VACUUM HOSE

BREATHER HOSE

CONNECTORS

Manuals by Motomatrix / www.motomatrix.co.uk / The Solution For Lost Motorcycle Coded Keys.

email: [email protected]

Summary of Contents for CBF600N













































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for CBF600N

Reviews:

Honda CBF600N, Service Manual, Page: 177 / 620

Search results

Summary of Contents for CBF600N

Reviews: