Honda CBF600N Service Manual Download Page 595

Page: 595 / 620

IMMOBILIZER SYSTEM (HISS)

21-7

HISS DIAGNOSTIC INFORMATION

Lift and support the fuel tank (page 3-5).
Disconnect the CKP sensor 2P (Red) connector.

Connect the inspection adaptor to the wire harness
side connector.

Connect the Red clip of the adaptor to the 12 V bat-
tery positive (+) terminal and green clip to the nega-
tive (–) terminal.

Turn the ignition switch to "ON" with the properly
registered key.

The immobilizer indicator will come on for approx.
ten seconds then it will start blinking to indicate the
diagnostic code if the system is abnormal.

The blinking frequency is repeated.

• The immobilizer indicator remains on when the

system is normal. (The system is in the normal
mode and the diagnostic code does not appear.)

HISS DIAGNOSTIC CODE

When the system (ECM) enters the diagnostic mode from the normal mode:

TOOLS:
Inspection harness

07XMZ-MBW0101

Test harness adaptor

070MZ-MEC0101

2P (Red) CONNECTOR

INSPECTION
HARNESS

ADAPTOR

IMMOBILIZER INDICATOR

S/SA model:

N/NA model:

BLINKING PATTERN

SYMPTOM

PROBLEM

PROCEDURE

ECM data is
abnormal.

Faulty ECM

Replace the ECM.

Code signals
cannot send or
receive.

Faulty immobi-
lizer receiver or
wire harness

Follow the trouble-
shooting (page 21-
9).

Identification
code is dis-
agree.

Jamming by the
other transpon-
der

Keep the other
vehicle's transpon-
der key away from
the immobilizer
receiver more than
50 mm (2.0 in).

Secret code is
disagree.

Manuals by Motomatrix / www.motomatrix.co.uk / The Solution For Lost Motorcycle Coded Keys.

email: [email protected]

Summary of Contents for CBF600N













































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for CBF600N

Reviews:

Honda CBF600N, Service Manual, Page: 595 / 620

Search results

Summary of Contents for CBF600N

Reviews: