Honda CBF600N Service Manual Download Page 585

Page: 585 / 620

LIGHTS/METERS/SWITCHES

20-37

Remove the bolt and sidestand switch.

Install the sidestand switch by aligning the switch
pin with the sidestand hole and the switch groove
with the holding pin.

Secure the sidestand switch with a new bolt.

Install the removed parts in the reverse order of
removal.

HORN

INSPECTION

Disconnect the wire connectors from the horn.

Connect the 12V battery to the horn terminal
directly and check the horn sound.

SIDESTAND SWITCH

BOLT

SIDESTAND SWITCH

HOLDING PIN

HOLE

Route the

sidestand wire

properly (page 1-

24).

BOLT

HORN

Manuals by Motomatrix / www.motomatrix.co.uk / The Solution For Lost Motorcycle Coded Keys.

email: [email protected]

Summary of Contents for CBF600N













































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for CBF600N

Reviews:

Honda CBF600N, Service Manual, Page: 585 / 620

Search results

Summary of Contents for CBF600N

Reviews: