Honda CBF600N Service Manual Download Page 580

Page: 580 / 620

LIGHTS/METERS/SWITCHES

20-32

HANDLEBAR SWITCHES

Remove the front center cowl unit (page 2-10).

Disconnect the handlebar switch connectors.

Remove the headlight unit (page 20-9).

Disconnect the handlebar switch connectors.

RIGHT HANDLEBAR SWITCH

Check for right handle switch continuity between
the wire terminals of the handlebar switch connec-
tor.

Continuity should exist between the terminals as
follows:

RIGHT HANDLEBAR SWITCH:

CBF600S/SA

RIGHT HANDLEBAR SWITCH 9P (Brown)
AND 2P (Natural) CONNECTOR

LEFT HANDLEBAR SWITCH 6P (Blue) AND
4P (Black) CONNECTOR

CBF600N/NA:

RIGHT HANDLEBAR SWITCH 9P (Brown)
AND 2P (Natural) CONNECTOR

LEFT HANDLEBAR SWITCH 6P (Blue) AND
6P (Black) CONNECTOR

ENGINE STOP SWITCH

STARTER SWITCH

HAZARD SWITCH

Manuals by Motomatrix / www.motomatrix.co.uk / The Solution For Lost Motorcycle Coded Keys.

email: [email protected]

Summary of Contents for CBF600N













































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for CBF600N

Reviews:

Honda CBF600N, Service Manual, Page: 580 / 620

Search results

Summary of Contents for CBF600N

Reviews: