Honda CBF600N Service Manual Download Page 181

Page: 181 / 620

FUEL SYSTEM (PGM-FI)

5-67

DISASSEMBLY

Disconnect the IAT sensor 2P (Gray) connector.

Remove the screws, IAT sensor and O-ring.

Disconnect the IDC solenoid valve 2P (Gray) connec-
tor.

Disconnect the TP sensor 3P (Black) connector.

Disconnect the MAP sensor 3P (Black) connector.

Disconnect the vacuum hose from the MAP sensor.
Remove the screw and MAP sensor from the air
cleaner housing.

2P (Gray) CONNECTOR

SCREWS

IAT SENSOR

O-RING

2P (Gray) CONNECTOR

3P (Black) CONNECTOR

VACUUM HOSE

SCREW

3P (Black) CONNECTOR

MAP SENSOR

Manuals by Motomatrix / www.motomatrix.co.uk / The Solution For Lost Motorcycle Coded Keys.

email: [email protected]

Summary of Contents for CBF600N













































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for CBF600N

Reviews:

Honda CBF600N, Service Manual, Page: 181 / 620

Search results

Summary of Contents for CBF600N

Reviews: