manualshive.com logo in svg

Honda CBF600N, Service Manual, Page: 235 / 620

Share
Download
Honda CBF600N Service Manual Download Page 235

COOLING SYSTEM

6-17

N/NA only:

Install the radiator grill while aligning the tabs to
hooks on radiator.

RADIATOR RESERVE TANK

REMOVAL/INSTALLATION

Remove the rear fender (page 2-6). 

Disconnect the siphon hose and overflow hose from
the reserve tank.

Remove the bolt and radiator reserve tank.

Installation is in the reverse order of removal.

Fill the reserve tank with coolant (page 6-7).

WATER PUMP

MECHANICAL SEAL INSPECTION

Check for signs of coolant leakage. A small amount
of "weeping" from the bleed hole is normal.

RADIATOR GRILL

HOOKS

Refer to the wires

properly

(page 1-24).

SIPHON HOSE

RESERVE TANK

OVERFLOW HOSE

BOLT

BLEED HOLE

WATER PUMP

Manuals by Motomatrix / www.motomatrix.co.uk / The Solution For Lost Motorcycle Coded Keys.

email: [email protected]

Summary of Contents for CBF600N













































































































































































































































































































































































































































































































































































































































Reviews:

No comments