HEIDENHAIN GAGE-CHEK 2000 Operating Instructions Manual Download Page 58

Page: 58 / 250

Information for OEM and Setup users | Mounting

2.2.3

Mounting on Multi-Pos stand

Use the provided M4 x 8 ISO 14581 countersunk head screws (black) to fasten

the stand to the threaded holes on the rear panel

Comply with the permissible tightening torque of 2.6 Nm

Using two M5 screws, you can also optionally screw the stand to a supporting

surface from the bottom
Adjust the desired angle of inclination
To fix the stand: Tighten the T25 screw

Comply with the tightening torque for screw T25

Recommended tightening torque: 5.0 Nm
Maximum permissible tightening torque: 15.0 Nm

Route the cable from behind through the two supports of the stand and then

through the lateral openings to the connections

Figure 15: Product mounted on Multi-Pos

stand

Figure 16: Cable routing on Multi-Pos stand

Further information:

"Product dimensions with Multi-Pos stand", Page 192

HEIDENHAIN | GAGE-CHEK 2000 | Operating Instructions | 06/2022

Summary of Contents for GAGE-CHEK 2000



























































































































































































































































Search results

Summary of Contents for GAGE-CHEK 2000

Reviews:

Brands by name

Popular brands

HEIDENHAIN GAGE-CHEK 2000, Operating Instructions Manual

Search results

Summary of Contents for GAGE-CHEK 2000

Reviews:

Brands by name

Popular brands