manualshive.com logo in svg

HEIDENHAIN GAGE-CHEK 2000, Operating Instructions Manual

Share
Download
HEIDENHAIN GAGE-CHEK 2000 Operating Instructions Manual Download Page 56

Information for OEM and Setup users | Mounting

 

II

 

2.2.1

Mounting on Single-Pos stand

You can fasten the Single-Pos stand to the product at a 20° angle.

Use the provided M4 x 8 ISO 14581 countersunk head screws to fasten the stand

to the upper threaded holes on the rear panel

Comply with the permissible tightening torque of 2.6 Nm

Fasten the stand with two suitable screws from above to a supporting surface

or

Attach self-adhesive rubber pads to the underside of the stand
Route the cables from behind through the opening in the stand and then to the

connections

Figure 11: Product mounted on Single-Pos

stand

Figure 12: Cable routing on Single-Pos

stand

Further information:

 "Product dimensions with Single-Pos stand", Page 191

56

HEIDENHAIN | GAGE-CHEK 2000 | Operating Instructions | 06/2022

Summary of Contents for GAGE-CHEK 2000



























































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands