manualshive.com logo in svg

HEIDENHAIN GAGE-CHEK 2000, Operating Instructions Manual

Share
Download
HEIDENHAIN GAGE-CHEK 2000 Operating Instructions Manual Download Page 25

General information | Basic operation

3.4.3

Switching off the GAGE-CHEK 2000

NOTICE

Damage to the operating system!

Disconnecting the power source while the product is on can damage the

operating system of the product.

Use the 

Switch-off

 menu to shut down the product

Do not disconnect the power source while the product is on
Do not turn the power switch off until the product has shut down

Tap 

Switch off

 in the main menu

Tap 

Shut down

The operating system shuts down
Wait until the following message appears on the screen:

You can switch off the device now.

Turn the power switch off

3.5

User login and logout

In the 

User login

 menu, you can log in and out of the product as a user.

Only one user can be logged in to the product at a time. The logged-in user is

displayed. Before a new user can log in, the logged-in user has to log out.

The product provides various authorization levels that grant the user full

or restricted access to management and operation functionality.

I

HEIDENHAIN | GAGE-CHEK 2000 | Operating Instructions | 06/2022

25

Summary of Contents for GAGE-CHEK 2000



























































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands