HEIDENHAIN GAGE-CHEK 2000 Operating Instructions Manual Download Page 53

Page: 53 / 250

Information for OEM and Setup users | Transport and storage

1.5.1

Repackaging the product

Repackaging should correspond to the original packaging as closely as possible.

Re-attach all mounting parts and dust protection caps to the product as received

from the factory, or repackage them in the original packaging as received from

the factory
Repackage the product in such a way that

it is protected from impact and vibration during transit
it is protected from the ingress of dust or humidity

Place all accessories that were included in the shipment in the original packaging

Further information:

"Items supplied and accessories", Page 49

Enclose all the documentation that was included in the original packaging

Further information:

"Storage and distribution of the documentation", Page 11

If the product is returned for repair to the Service department:

Ship the product without accessories, without encoders and without

peripherals

1.5.2

Storage of the product

Package the product as described above
Observe the specified ambient conditions

Further information:

"Specifications", Page 186

Inspect the product for damage after any transport or longer storage times

HEIDENHAIN | GAGE-CHEK 2000 | Operating Instructions | 06/2022

Summary of Contents for GAGE-CHEK 2000



























































































































































































































































Search results

Summary of Contents for GAGE-CHEK 2000

Reviews:

Brands by name

Popular brands

HEIDENHAIN GAGE-CHEK 2000, Operating Instructions Manual

Search results

Summary of Contents for GAGE-CHEK 2000

Reviews:

Brands by name

Popular brands