manualshive.com logo in svg

HEIDENHAIN GAGE-CHEK 2000, Operating Instructions Manual

Share
Download
HEIDENHAIN GAGE-CHEK 2000 Operating Instructions Manual Download Page 151

Information for OEM and Setup users | File management

6.1

Overview

This chapter describes the 

File management

 menu and its functions.

Make sure that you have read and understood the "Basic operation"

chapter before carrying out the actions described below.

Further information:

 "Basic operation", Page 19

Short description

The 

File management

 menu shows an overview of the files stored in the product's

memory.
Any connected USB mass storage devices (FAT32 format) or available network

drives are shown in the list of storage locations. The USB mass storage devices and

the network drives are displayed with their name or drive designation.

Call

Tap 

File management

 in the main menu

The file management user interface is displayed

1

2

Figure 25: 

File management

 menu

1

List of available storage locations

2

List of folders in the selected storage location

II

HEIDENHAIN | GAGE-CHEK 2000 | Operating Instructions | 06/2022

151

Summary of Contents for GAGE-CHEK 2000



























































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands