HEIDENHAIN GAGE-CHEK 2000 Operating Instructions Manual Download Page 159

Page: 159 / 250

Information for OEM and Setup users | Settings

7.2

General

This chapter describes settings for configuring the operation and display .

Parameter

Further information

Device information

"Device information", Page 159

Screen

"Screen", Page 160

Display

"Display", Page 160

Input devices

"Configuring operation with a mouse or touchscreen",

Page 132

Sounds

"Sounds", Page 161

Printers

"Printers", Page 161

Date and time

"Setting the date and time", Page 79

Units

"Setting the units of measure", Page 79

Function bar

"Function bar", Page 162

Copyrights

"Copyrights", Page 162

Service info

"Service info", Page 162

Documentation

"Documentation", Page 162

7.2.1

Device information

Settings

►

General

►

Device information

The overview displays basic information about the software.

Parameter

Displays the information

Product designation

Product designation of the product

Part number

ID number of the unit

Serial number

Serial number of the product

Firmware version

Version number of the firmware

Firmware built on

Firmware creation date

Last firmware update on

Date of most recent firmware update

Free memory space

Free memory space in the internal storage location

Internal

Free working memory (RAM)

Free RAM on the system

Number of unit starts

Number of times the product was started up with the current

firmware

Operating time

Operating time of the product with the current firmware

HEIDENHAIN | GAGE-CHEK 2000 | Operating Instructions | 06/2022

159

Summary of Contents for GAGE-CHEK 2000



























































































































































































































































Search results

Summary of Contents for GAGE-CHEK 2000

Reviews:

Brands by name

Popular brands

HEIDENHAIN GAGE-CHEK 2000, Operating Instructions Manual

Search results

Summary of Contents for GAGE-CHEK 2000

Reviews:

Brands by name

Popular brands