manualshive.com logo in svg

HEIDENHAIN GAGE-CHEK 2000, Operating Instructions Manual

Share
Download
HEIDENHAIN GAGE-CHEK 2000 Operating Instructions Manual Download Page 234

Information for the Operator user | Sending measured values to a computer

 

III

 

12

Sending measured values to a computer

12.1

Configuring the measured value output

The product offers you various functions for manual or automatic transfer of the

acquired measured values to a computer.

Prerequisites:

The product is connected to the computer
Receiving software is installed on the computer

The following steps are necessary in order to configure the measured value output:

Configuring an interface
Select the data format (only for RS-232)
Adding the desired function elements to the function bar
Selecting contents for the data transfer

If you connect a USB-to-RS232 connecting cable from the manufacturer

STEINWALD datentechnik GmbH to the product, the data interface is

configured automatically and is ready immediately. The data format

Steinwald

 is used for measured value output. The settings are not

configurable.

234

HEIDENHAIN | GAGE-CHEK 2000 | Operating Instructions | 06/2022

Summary of Contents for GAGE-CHEK 2000



























































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands