manualshive.com logo in svg

Harris Intelligent Transmitter Platinum-i Series, Technical Manual

The Harris Intelligent Transmitter Platinum-i Series is a cutting-edge device designed to provide exceptional performance in transmitting data. To assist users in understanding its advanced features and functionalities, we offer a comprehensive Technical Manual for free download. Visit our website to access this invaluable resource and make the most out of your Platinum-i transmitter.

Share
Download
background image

 

______________________________________________

HARRIS

 

 

888-9058-001 

WARNING: Disconnect and lockout AC primary power prior to servicing

 

35

 

l.

 

The electrical and RF plumbing work should begin at the start of the installation 

in order not to delay completion, however the transmitter, RF output system and 
cooling system plumbing should be installed prior to running electrical conduits 
or air handling ducts in the transmitter space. This will prevent interference issues 
between RF lines and electrical conduit and cooling ductwork. 
 

m.

 

Hanging hardware must be on-hand to avoid delays. Ensure that all pipe hangers, 

conduit hangers, threaded rod, beam clamps, Unistrut and Unistrut hardware are 
on site. 

 

Ensure that all necessary tools are on site and in good shape when needed. Check 
transmitter and other equipment technical manuals to see if any specialized tools are 
required. Make arrangements to obtain them if necessary. 
 

2.2.0.1 Space Requirements 

(Refer to Transmitter Outline drawings.) 
 
To allow for servicing the transmitter, a minimum clearance of 4 feet in front of and 5 
feet behind the cabinets is recommended. Minimum clearances are shown in the 
drawings. 
 
Planning for the transmitter room should allow space for program input, monitoring, 
remote control, and test equipment as well as the transmitter. Additional area may also 
be required for tower lighting, HVAC equipment, storage, and a workbench. 
 

2.2.1 Weights 

Weights are listed below each cabinet on the Transmitter Outline drawing. Be sure to 
include this information in your planning for the building and verify that the structure is 
capable of safely supporting the total weight of the transmitter and its peripheral 
equipment. The 50 Volt power supplies are furnished with two metal wheels for easy 
movement and installation in the transmitter. 
 
Consider the type of floor on which the power supply will rest. The weight is carried on 
two wheels, which will possibly mar the floor. Long term weight may damage the floor, 
making power supply removal for maintenance very difficult. Protection of tiled floors 
should be considered. 
 

2.2.2 RF System Layout 

Refer to the RF Layout drawing for the transmitter and RF system floor plan. A system 
of overhead supports and hangers is needed to support the coaxial lines, filters, and 
other RF components. The support system should be installed so that the RF 
components are completely supported by the hangers, to minimize the weight carried 
by the output connectors at the top of the cabinets. 

 
 

Summary of Contents for Intelligent Transmitter Platinum-i Series





























































































































































































































Reviews:

No comments

Related manuals for Intelligent Transmitter Platinum-i Series

halstrup-walcher PIZ Instruction Manual preview
PIZ
Brand: halstrup-walcher Pages: 12
Questtel L-RF-32mW-TX User Manual preview
L-RF-32mW-TX
Brand: Questtel Pages: 15
Icom IC-F3GT Instruction Manual preview
IC-F3GT
Brand: Icom Pages: 32
A-Neuvideo ANI-HDR-70 Instruction Manual preview
ANI-HDR-70
Brand: A-Neuvideo Pages: 12
Datcon DT7200 Series User Manual preview
DT7200 Series
Brand: Datcon Pages: 24
Rover RLT-1550 D10 Operating Manual preview
RLT-1550 D10
Brand: Rover Pages: 27
Apache Labs ANAN-200D User Manual preview
ANAN-200D
Brand: Apache Labs Pages: 67
WAREMA EWFS Operating And Installation Instructions preview
EWFS
Brand: WAREMA Pages: 6
Icom ID-31A PLUS Advanced Manual preview
ID-31A PLUS
Brand: Icom Pages: 227
Icom ID-5100A Basic Manual preview
ID-5100A
Brand: Icom Pages: 108
Intek M-899 VOX Owner'S Manual preview
M-899 VOX
Brand: Intek Pages: 36
Intek TM-200S Owner'S Manual preview
TM-200S
Brand: Intek Pages: 40
WIKA UPT-2 Series Operating Instructions Manual preview
UPT-2 Series
Brand: WIKA Pages: 140
F.u.n.k.e. 833-II-(Axxx)-(Axxx) series Operation And Installation preview
833-II-(Axxx)-(Axxx) series
Brand: F.u.n.k.e. Pages: 56
Paradox Magellan DCTXP2 User Manual preview
Magellan DCTXP2
Brand: Paradox Pages: 3
Icom IC-M401EURO Instruction Manual preview
IC-M401EURO
Brand: Icom Pages: 32
MadgeTech RFC1000-IP69K User Manual preview
RFC1000-IP69K
Brand: MadgeTech Pages: 12
ChatterBox GMRS XI Manual preview
GMRS XI
Brand: ChatterBox Pages: 24

Brands by name

Popular brands

Load more brands