manualshive.com logo in svg

GE N60, Instruction Manual

Introducing the Lenovo N60 - a sleek and powerful device designed to enhance your everyday computing experience. Get started quickly with our comprehensive Quick Start Manual, available for free download at manualshive.com. Access the manual effortlessly and uncover the full potential of your Lenovo N60.

Share
Download
background image

3-40

N60 NETWORK STABILITY AND SYNCHROPHASOR MEASUREMENT SYSTEM – INSTRUCTION MANUAL

DIRECT INPUT AND OUTPUT COMMUNICATIONS

CHAPTER 3: INSTALLATION

3

Figure 3-44: Two-channel two-clock RS422 interface connections

3.4.7  RS422 and fiber interface

The following figure shows the combined RS422 plus fiberoptic interface configuration at 64 K baud. The 7L, 7M, 7N, 7P, 
and 74 modules are used in two-terminal with a redundant channel or three-terminal configurations where channel 1 is 
employed via the RS422 interface (possibly with a multiplexer) and channel 2 via direct fiber.
AWG 20-24 twisted shielded pair is recommended for external RS422 connections and ground the shield only at one end. 
For the direct fiber channel, address power budget issues properly.

Figure 3-45: RS422 and fiber interface connection

The connections shown in the figure are for multiplexers configured as data communications equipment (DCE) units.

3.4.8  IEEE C37.94 interface

The UR-series IEEE C37.94 communication modules (module types 2G, 2H, 2I, 2J, 76, and 77) are designed to interface with 
IEEE C37.94 compliant digital multiplexers or an IEEE C37.94 compliant interface converter for use with direct input and 
output applications. The IEEE C37.94 standard defines a point-to-point optical link for synchronous data between a 
multiplexer and a teleprotection device. This data is typically 64 kbps, but the standard provides for speeds up to 64

n

 kbps, 

where n = 1, 2,…, 12. The UR-series C37.94 communication modules are either 64 kbps (with n fixed at 1) for 128 kbps (with 
n fixed at 2). The frame is a valid International Telecommunications Union (ITU-T) recommended G.704 pattern from the 
standpoint of framing and data rate. The frame is 256 bits and is repeated at a frame rate of 8000 Hz, with a resultant bit 
rate of 2048 kbps.
The specifications for the module are as follows:

When using a laser interface, attenuators can be necessary to ensure that you do not exceed 
maximum optical input power to the receiver.

Summary of Contents for N60



























































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for N60

ABB LME620-AI Service Instruction preview
LME620-AI
Brand: ABB Pages: 30
ABB LME620-AI Instructions Manual preview
LME620-AI
Brand: ABB Pages: 15
ABB PST30 Manual preview
PST30
Brand: ABB Pages: 10
ABB LME620-AI User Manual preview
LME620-AI
Brand: ABB Pages: 44
Gardena Master Operator'S Manual preview
Master
Brand: Gardena Pages: 18
Danfoss VLT Micro Drive FC 51 Series Quick Manual preview
VLT Micro Drive FC 51 Series
Brand: Danfoss Pages: 23
Danfoss VLT series Quick Manual preview
VLT series
Brand: Danfoss Pages: 37
Daikin MicroTech II Operation And Maintenance Manual preview
MicroTech II
Brand: Daikin Pages: 44
Vaillant VRT 340f Operating Instruction preview
VRT 340f
Brand: Vaillant Pages: 32
Vaillant VRT 330 Manual preview
VRT 330
Brand: Vaillant Pages: 27
Vaillant VRC 470 Operating Instructions Manual preview
VRC 470
Brand: Vaillant Pages: 40
Vaillant VRT 350f Installation Instructions Manual preview
VRT 350f
Brand: Vaillant Pages: 36
Vaillant VRT 350 Installation Instructions Manual preview
VRT 350
Brand: Vaillant Pages: 28
Vaillant VAZ CPC Operating Instructions Manual preview
VAZ CPC
Brand: Vaillant Pages: 92
SYCLOPE electronic TRACE'O Installation And Starting Instructions preview
TRACE'O
Brand: SYCLOPE electronic Pages: 40
Timotion TDH6PR Series Manual preview
TDH6PR Series
Brand: Timotion Pages: 10
Technische Alternative UVR 63H Operation And Installation Manual preview
UVR 63H
Brand: Technische Alternative Pages: 68
TechGrow Humi DualPro User Manual preview
Humi DualPro
Brand: TechGrow Pages: 34

Brands by name

Popular brands

Load more brands