GE N60 Instruction Manual Download Page 431 | Manualshive

Page: 431 / 666

background image

CHAPTER 5: SETTINGS

GROUPED ELEMENTS

N60 NETWORK STABILITY AND SYNCHROPHASOR MEASUREMENT SYSTEM – INSTRUCTION MANUAL

5-237

5

The neutral directional overcurrent element provides both forward and reverse fault direction indications for the

NEUTRAL

DIR OC1 FWD

and

NEUTRAL DIR OC1 REV

operands, respectively. The output operand is asserted if the magnitude of the

operating current is above a pickup level (overcurrent unit) and the fault direction is seen as forward or reverse,
respectively (directional unit).
The

overcurrent unit

responds to the magnitude of a fundamental frequency phasor of either the neutral current

calculated from the phase currents or the ground current. There are separate pickup settings for the forward-looking and
reverse-looking functions. If set to use the calculated 3I_0, the element applies a positive-sequence restraint for better
performance: a small user-programmable portion of the positive-sequence current magnitude is subtracted from the
zero-sequence current magnitude when forming the operating quantity.

I

op

= 3 x (|I_0| - K x |I_1|)

Eq. 5-20

The positive-sequence restraint allows for more sensitive settings by counterbalancing spurious zero-sequence currents
resulting from
•

System unbalances under heavy load conditions

•

Transformation errors of current transformers (CTs) during double-line and three-phase faults

•

Switch-off transients during double-line and three-phase faults

The positive-sequence restraint must be considered when testing for pickup accuracy and response time (multiple of
pickup). The operating quantity depends on the way the test currents are injected into the relay (single-phase injection:
I

op

= (1 – K)

×

I

injected

; three-phase pure zero-sequence injection: I

op

= 3

×

I

injected

.

The positive-sequence restraint is removed for low currents. If the positive-sequence current is below 0.8 pu, the restraint is
removed by changing the constant K to zero. This facilitates better response to high-resistance faults when the unbalance
is very small and there is no danger of excessive CT errors as the current is low.
The

directional unit

uses the zero-sequence current (I_0) or ground current (IG) for fault direction discrimination and can

be programmed to use either zero-sequence voltage (“Calculated V0” or “Measured VX”), ground current (IG), or both for
polarizing. The zero-sequence current (I_0) must be greater than the

PRODUCT SETUP



DISPLAY PROPERTIES



CURRENT

CUT-OFF LEVEL

setting value and IG must be greater than 0.05 pu to be validated as the operating quantity for directional

current. The following tables define the neutral directional overcurrent element. V_0 is the zero-sequence voltage, I_0 is
the zero-sequence current, ECA is the element characteristic angle, and IG is the ground current.



NEUTRAL DIR OC1

OFFSET: 0.00

Ω

Range: 0.00 to 250.00

Ω

in steps of 0.01



NEUTRAL DIR OC1 FWD

ECA: 75° Lag

Range: –90 to 90° in steps of 1



NEUTRAL DIR OC1 FWD

LIMIT ANGLE: 90°

Range: 40 to 90° in steps of 1



NEUTRAL DIR OC1 FWD

PICKUP: 0.050 pu

Range: 0.006 to 30.000 pu in steps of 0.001



NEUTRAL DIR OC1 REV

LIMIT ANGLE: 90°

Range: 40 to 90° in steps of 1



NEUTRAL DIR OC1 REV

PICKUP: 0.050 pu

Range: 0.006 to 30.000 pu in steps of 0.001



NEUTRAL DIR OC1 BLK:

Off

Range: FlexLogic operand



NEUTRAL DIR OC1

TARGET: Self-reset

Range: Self-reset, Latched, Disabled



NEUTRAL DIR OC1

EVENTS: Disabled

Range: Disabled, Enabled

«
...
429
430
431
432
433
...
»

Summary of Contents for N60



























































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for N60

Brand: VAT Pages: 26

Brand: Taie Pages: 28

Brand: Vega Pages: 20

Brand: We Care Solar Pages: 46

Brand: Watts Pages: 4

OneFlow OFTWH-R

Brand: Watts Pages: 8

Brand: YOKOGAWA Pages: 150

Brand: YOODA Pages: 3

Brand: YMGI Pages: 8

Brand: Tylo Pages: 51

Brand: Insignia Pages: 2

Brand: Thermomart Pages: 6

Brand: GSD Pages: 5

eTracer ET4415BND

Brand: Epsolar Pages: 44

Brand: Graco Pages: 166

Brand: Baby Trend Pages: 10

Brand: HEROSE Pages: 92

Brand: QUICK DAM Pages: 16

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands