GE Centricity RA600 Service Manual Download

Page: 174 / 278

Functional Check

VF 003 Customer Turnover

Page 174

Customer turnover completed by:___________________ Date Completed: __________________

Check off

Task Completed

Ensure fans and other devices are clear of foreign bodies and functional.

Confirm images can be displayed on the graphical user interface.

Monitor(s) calibrated per procedure.

If applicable. default route information is added.

If applicable. verify that images sent to the printer(s) print correctly.

The workstation configuration data has been backed up to the 3.5” diskette
and stored away.

Ethernet pings performed.

Administrator password is set.

Save System & User settings & show customer where they are saved

Instruct customer in use of Settings Tool to save & restore System and User
settings

Summary of Contents for Centricity RA600























































































































































































































































































Search results

Summary of Contents for Centricity RA600

Reviews:

Related manuals for Centricity RA600

Brands by name

Popular brands

GE Centricity RA600, Service Manual

Search results

Summary of Contents for Centricity RA600

Reviews:

Related manuals for Centricity RA600

Brands by name

Popular brands