manualshive.com logo in svg

GE Centricity RA600, Service Manual

Share
Download
GE Centricity RA600 Service Manual Download Page 210

Software Procedures

SW 008 Common Windows 2000 Procedures

Page 210

Table 6-2: Common Windows 2000 Procedures List

Section 2: Startup / Shutdown

2-1 Booting Workstation from a Power Off Condition

Note:

System will take about two minutes to boot, if using portrait monitors, no video will be displayed 
until the system has booted.

1.

Verify the power is applied to the monitor (the on/off switch is located on the lower rear side of 
the Barco monitor).

2.

Verify that power is applied to the workstation (the on/off switch is located on the center right 
front of the CPU tower).

3.

With the power applied to all the peripheral devices and to the workstation, the workstation will 
self boot the operating system (Windows 2000). 

2-2 Shutdown Workstation Operating System

1.

Click on 

Start

.

2.

Click on 

Shut Down

.

8-1

Displaying Application Programs

8-2

Starting Application Programs

8-3

Changing Screen Saver Properties (wait value)

Section

Topic

Summary of Contents for Centricity RA600























































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands