Fujitsu MB91F109 Hardware Manual Download Page 161 | Manualshive

Page: 161 / 461

background image

137

4.14 DRAM Signal Control Register (DSCR)

[bit 3] C0HE

The C0HE bit controls the CS0H output. When this bit is reset, the output is inhibited.

0: Inhibits output (initial value).

1: Permits output.

[bit 2] C0LE

The C0LE bit controls the CS0L output. When this bit is reset, the output is inhibited.

0: Inhibits output (initial value).

1: Permits output.

[bit 1] RS1E

The RS1E bit controls the RAS1 output. When this bit is reset, the output is inhibited.

In this device type, because the RAS1 pin also serves as the DMAC E0P2 output, it is
controlled together with the EPSE2 and EPDE2 bits of the DMAC control register (DATCR)
as shown below.

[bit 0] RS0E

The RS0E bit controls the RAS0 output. When this bit is reset, the output is inhibited.

0: Inhibits output (initial value).

1: Permits output.

EPSE2

EPDE2

RS1E

0
0
0
1
1

0
0
1
0
1

0
1

X
X
X

Port (initial value)
RAS1 output
E0P2 output
E0P2 output
E0P2 output

«
...
159
160
161
162
163
...
»

Summary of Contents for MB91F109














































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for MB91F109

Brand: Hama Pages: 4

Brand: Yamaha Pages: 24

Brand: Yamaha Pages: 5

Brand: Q-See Pages: 2

Brand: Renesas Pages: 20

Extreme Gaming VGA Cooler GV1000

Brand: ZALMAN Pages: 7

Brand: IFM Electronic Pages: 14

Brand: MEDIATEK Pages: 166

Brand: Comtrend Corporation Pages: 4

Brand: UMAX Technologies Pages: 27

DUAL Nx56/64 1200142L1#

Brand: ADTRAN Pages: 48

Brand: Disc Makers Pages: 12

Brand: ZALMAN Pages: 8

Brand: NEC Pages: 114

Brand: Z3 Technology Pages: 94

BD7682FJ-EVK-301

Brand: Rohm Pages: 6

Brand: Devolo Pages: 24

Brand: Magnescale Pages: 73

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands