Fujitsu MB91F109 Hardware Manual Download Page 281 | Manualshive

Page: 281 / 461

background image

257

10.7 Asynchronous (Start-Stop) Mode

10.7 Asynchronous (Start-Stop) Mode

The UART handles data of only NRZ (nonreturn-to-zero) format.
Data transfer begins with a start bit (L-level data) for the specified number of data bits
in LSB first mode and ends with a stop bit (H-level data). When the external clock is
selected, always input the clock signal.

■

Format of Data Transferred in Asynchronous (Start-Stop) Mode

Figure 10.7-1 shows the format of data transferred in asynchronous (start-stop) mode.

The data length can be seven or eight bits in normal mode (mode 0), but must be eight bits in
multiprocessor mode (mode 1). An A/D bit is always added to data in multiprocessor mode
instead of a parity bit.

Figure 10.7-1 Format of Data Transferred in Asynchronous (Start-Stop) Mode (Mode 0 or 1)

❍

Receive operation

The UART performs a receive operation as long as the RXE bit (bit 1) of the SCR register is "1".

When a start bit appears on the receiving line, one data frame is received based on the data
format specified by the SCR register. If an error occurs after a frame has been received, an
error flag is set and the RDRF flag (bit 4 of the SSR register) is set subsequently, thereby
causing a receiver interrupt to the CPU if the RIE bit (bit 1) of the same SSR register has been
set to "1". Ensure in the program design that the flags of the SSR register are checked and the
SIDR register is read if normal reception is indicated, while the necessary processing for a
countermeasure is performed if an error is indicated.

The RDRF flag is cleared when the SIDR register is read.

❍

Transmit operation

Transmission data is written to the SODR register when the TDRE flag (bit 11) of the SSR
register is "1". When the TXE bit (bit 0) of the SCR register is "1", the written data is
transmitted.

When the data written to the SODR register is loaded to the transmission shift register and
transmission begins, the TDRE flag is set again so that the next instance of transmission data
can be written. If the TIE bit (bit 0) of the same SSR register has been set to "1", a transmitter
interrupt occurs in the CPU and a request to write transmission data to the SODR register is
issued.

The TDRE flag is cleared when data is written to the SODR register.

SI,SO

Start

LSB

MSB Stop

A/D Stop

Transferred data is 01001101

(Mode 0)

(Mode 1)

0

1

0

0

0

0

1

1

1

B

«
...
279
280
281
282
283
...
»

Summary of Contents for MB91F109














































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for MB91F109

Brand: Pima Pages: 4

X-Pedition 2000

Brand: Enterasys Pages: 86

PG-FLEX RT FRL-752

Brand: PairGain Pages: 6

Brand: Cypress Semiconductor Pages: 11

Brand: IEI Technology Pages: 86

Lite N42B1P Series

Brand: Dahua Technology Pages: 14

IntroSpect Analyzer 2 Series

Brand: Aruba Pages: 5

Brand: peplink Pages: 2

Brand: Kontron Pages: 42

Brand: ICP DAS USA Pages: 62

Homecraft Rolyan AA6240

Brand: Patterson Pages: 2

Brand: Omron Pages: 11

Cascade Express

Brand: Riverbed Pages: 92

ST7-EMU3 Series

Brand: ST Pages: 39

StudioStation 100

Brand: Extron electronics Pages: 131

Ready Made Curtain

Brand: Kvadrat Pages: 10

Brand: SunFounder Pages: 527

TEW-630APB - Wireless Access Point

Brand: TRENDnet Pages: 56

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands