Fujitsu MB91F109 Hardware Manual Download Page 273 | Manualshive

Page: 273 / 461

background image

249

10.2 Serial Mode Register (SMR)

[bit 1] SCKE (SCLK Enable)

When communication is performed in CLK synchronous mode (mode 2), this bit specifies
whether to use the SC pin as a clock input pin or a clock output pin.

Set this bit to "0" in CLK asynchronous mode or external clock mode.

0: Clock input pin (initial value)

1: Clock output pin

<Note>

To use the SC pin as a clock input pin, set the CS0 bit in advance to 1 to select the external
clock.

[bit 0] SOE (Serial Output Enable)

There is an external pin (SO) that is also designed to be used for a general-purpose I/O port
pin. This bit specifies whether to use the external pin (SO) as a serial output pin or an I/O
port pin.

0: General-purpose I/O port pin (initial value)

1: Serial data output pin (SO)

«
...
271
272
273
274
275
...
»

Summary of Contents for MB91F109














































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for MB91F109

Brand: Xinje Pages: 57

Brand: Lab.gruppen Pages: 35

Brand: Lorex Pages: 186

Brand: MiLAN Pages: 1

PacketShaper PS-S200

Brand: Symantec Pages: 2

Brand: ZyXEL Communications Pages: 215

EK-FC285 GTX Classified

Brand: ekwb Pages: 2

TeleCLIENT TC7730 Series

Brand: ETL Pages: 83

Brand: ICP DAS USA Pages: 8

Brand: Penguin Edge Pages: 2

Brand: Aaeon Pages: 57

Brand: Juniper Pages: 196

BiPAC 5200S RC Series

Brand: Billion Pages: 79

Brand: Digital Voice Systems Pages: 32

Lexicon MPX 200

Brand: Harman Pages: 77

Brand: Nexus Pages: 9

Brand: Disc Makers Pages: 12

Brand: Xilinx Pages: 36

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands