manualshive.com logo in svg

Fujitsu MB90390 Series, Hardware Manual, Page: 452 / 740

Share
Download
Fujitsu MB90390 Series Hardware Manual Download Page 452

424

CHAPTER 21  400 kHz I

2

C INTERFACE

■

Ten Bit Address Mask Register (ITMK) Contents

Table 21.2-4  Function of Each Bit of the Ten Bit Address Mask Register (ITMK)

Bit name

Function

bit15

ENTB:
Enable ten bit 
slave address bit

This bit enables the ten bit slave address (and the acknowledging upon its reception). 
Write access to this bit is only possible if the interface is disabled (EN= 0 in ICCR).
"0": Ten bit address disabled
"1": Ten bit address enabled

bit14

RAL:
Received slave 
address length bit

This bit indicates whether the interface was addressed as a seven or ten bit slave. It is 
read only.
"0": Addressed as seven bit slave
"1": Addressed as ten bit slave
This bit can be used to determine whether the interface was addressed as a seven or ten 
bit slave if both slave addresses are enabled (ENTB = 1 and ENSB = 1). Its contents is 
only valid if the AAS bit in the IBSR register is "1". This bit is also reset if the interface 
is disabled (EN= 0 in ICCR).

bit13 to 

bit10

Undefined

These bits always return "1" during reading.

bit9 to bit0

TMK:
Ten bit slave 
address mask bits

This register is used to mask the ten bit slave address of the interface. Write access to 
these bits is only possible if the interface is disabled (EN= 0 in ICCR).
"0": Bit is not used in slave address comparison
"1": Bit is used in slave address comparison
This can be used to make the interface acknowledge on multiple ten bit slave addresses. 
Only the bits set to "1" in this register are used in the ten bit slave address comparison. 
The received slave address is written back to the ITBA register and thus may be 
determined by reading the ITBA register if the AAS bit in 
the IBSR register is "1".

Note:

If the address mask is changed after the interface had been enabled, the slave address 
should also be set again since it could have been overwritten by a previously 
received slave address.

Summary of Contents for MB90390 Series





































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments