manualshive.com logo in svg

Fujitsu MB90390 Series, Hardware Manual, Page: 183 / 740

Share
Download
Fujitsu MB90390 Series Hardware Manual Download Page 183

155

CHAPTER 8  LOW-POWER CONTROL CIRCUIT

Figure 8.5-2  Release of the Stop Mode (External Reset)

Notes:

•

To set a pin to high impedance when the pin is shared by a peripheral function and a port in stop
mode, disable the output of peripheral functions, and set the STP bit of the low-power
consumption mode control register (LPMCR) to "1".

This applies to the following pins:

P03/IN3/OUT6, P05/IN5/OUT7, P06/OUT0, P07/OUT1, P10/OUT2, P11/OUT3, P12/OUT4, 
P13/OUT5, P15/TOT0, P16/SGO, P17/SGA, P20/TX1, P31/TX0, P33/TOT1, P34/SOT0, P35/
SCK0

•

In PLL stop mode, the main clock and PLL multiplication circuit stop. During recovery from PLL
stop mode, it is necessary to allot the main clock oscillation stabilization wait time and PLL clock
oscillation stabilization wait time. The oscillation stabilization wait times for the main clock and
PLL clock are counted simultaneously according to the value specified in the oscillation
stabilization wait time selection bits (CKSCR: WS1, WS0) in the clock selection register. The
oscillation stabilization wait time selection bits (CKSCR: WS1, WS0) in the clock selection register
must be selected accordingly to account for the longer of main clock and PLL clock oscillation

stabilization wait time. The PLL clock oscillation stabilization wait time, however, requires 2

14

/

HCLK or more. Set the oscillation stabilization wait time selection bits (CKSCR: WS1, WS0) in the
clock selection register to "10

B

" or "11

B

". 

RST

pin

Stop mode

Main clock

PLL clock

CPU clock

CPU operation

Oscillation stabilization

w

ait

Oscillating

Inactive

Main clock

Reset released.

Stop mode released.

Reset sequence Execution

Inactive

Oscillating

Inactive

Summary of Contents for MB90390 Series





































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments