Ford 2012 F-150 Owner'S Manual Download Page 92

Page: 92 / 476

Replacing exterior mounted mirror turn signal indicator lamp bulbs

For bulb replacement, see your authorized dealer.

Replacing license plate lamp bulbs

The license plate bulbs are located
behind the rear bumper. To change
the license plate lamp bulbs:

1. Reach behind the rear bumper to
locate the bulb.

2. Twist the bulb socket
counterclockwise and carefully pull
to remove it from the lamp
assembly.

3. Pull out the old bulb from the
socket and push in the new bulb.

4. Install the bulb socket in lamp assembly by turning it clockwise.

Lights

2012 F-150

(f12)

Owners Guide, 2nd Printing
USA

(fus)

Summary of Contents for 2012 F-150





























































































































































































































































































































































































































































































Search results

Summary of Contents for 2012 F-150

Reviews:

Brands by name

Popular brands

Ford 2012 F-150, Owner'S Manual

Search results

Summary of Contents for 2012 F-150

Reviews:

Brands by name

Popular brands