manualshive.com logo in svg

Ford 2012 F-150, Owner'S Manual

Share
Download
Ford 2012 F-150 Owner'S Manual Download Page 57

Use

SEEK

to adjust between SPEED OFF and levels

1–7:

Increasing the level from 1 (lowest setting) to 7 (highest setting) allows
the radio volume to automatically change slightly with vehicle speed to
compensate for road and wind noise.
Recommended level is

1–3;

SPEED OFF turns the feature off and level 7

is the maximum setting.

Extra Features

AUX:

Press repeatedly to cycle through LINE IN (auxiliary audio mode),

and SYNC

威

(if equipped).

For location and further information on auxiliary audio mode, refer to

Auxiliary input jack

later in this chapter.

If your vehicle is equipped with SYNC

威

, please refer to supplemental

information on

SYNC

威

.

OK:

Your vehicle may be equipped

with special phone and media
features which will require you to
confirm commands by pressing OK.
For further information, refer to
supplemental information on

SYNC

威

.

(Phone):

If your vehicle is equipped with SYNC

威

, press to access

SYNC PHONE features. For further information, please refer to
supplemental information on

SYNC

威

.

If your vehicle is not equipped with SYNC

威

, the display may read NO

PHONE.

Audio system–Navigation system based (if equipped)

If your vehicle is equipped with the navigation system, it will have an
integrated navigation/audio system. See the

Navigation system

supplement for operating instructions on using this audio system.

Auxiliary input jack (Line in — if equipped)

WARNING:

Driving while distracted can result in loss of vehicle

control, accident and injury. Ford strongly recommends that

drivers use extreme caution when using any device or feature that may
take their focus off the road. Your primary responsibility is the safe
operation of the vehicle. We recommend against the use of any
handheld device while driving, encourage the use of voice-operated
systems when possible and that you become aware of applicable state
and local laws that may affect use of electronic devices while driving.

Entertainment Systems

57

2012 F-150

(f12)

Owners Guide, 2nd Printing
USA

(fus)

Summary of Contents for 2012 F-150





























































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands