manualshive.com logo in svg

Ford 2012 F-150, Owner'S Manual

Share
Download
Ford 2012 F-150 Owner'S Manual Download Page 168

WARNING:

To minimize the risk of neck injury in the event of a

crash, the driver and passenger occupants should not sit in

and/or operate the vehicle, until the head restraint is placed in its
proper position. The driver should never adjust the head restraint
while the vehicle is in motion.

The non-adjustable head restraints
consist of:

•

a trimmed energy absorbing foam
and structure (1),

•

two steel stems (2),

•

and two guide sleeve
unlock/remove buttons (3).

To remove the non-adjustable head restraint, do the following:

1. Simultaneously press and hold
both unlock/remove buttons, then
pull up on the head restraint.

To reinstall the non-adjustable head restraint, do the following:

1. Insert the two stems into the
guide sleeve collars.

2. Push the head restraint down
until it locks.

Seating and Safety Restraints

168

2012 F-150

(f12)

Owners Guide, 2nd Printing
USA

(fus)

Summary of Contents for 2012 F-150





























































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands