manualshive.com logo in svg

Ford 2012 F-150, Owner'S Manual

Share
Download
Ford 2012 F-150 Owner'S Manual Download Page 173

The control is located on the
outboard side of the seat. Move the
switch in the direction of the arrow
to raise or lower the seat cushion or
to move the seat forward, backward,
up or down.

Power Recline (if equipped)

Move the switch to recline the
seatback forward or rearward.

Power Lumbar (if equipped)

The control is located on the
outboard side of the seat. P ress the
forward or rearward side of the
control for more or less support.

Seating and Safety Restraints

173

2012 F-150

(f12)

Owners Guide, 2nd Printing
USA

(fus)

Summary of Contents for 2012 F-150





























































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands