manualshive.com logo in svg

Ford 2012 F-150, Owner'S Manual

Share
Download
Ford 2012 F-150 Owner'S Manual Download Page 80

Manual climate control

For hot weather conditions:

•

The climate control system will be set to MAX A/C.

For cold weather conditions:

•

The climate control system will be set to provide maximum heating
in

(floor/defrost) mode.

•

Rear defrost/heated mirrors (if equipped) will be activated.

For moderate weather conditions:

•

The interior cabin will be heated, cooled or off, based upon the
previous operating state (last ignition-on cycle).

•

Rear defrost/heated mirrors (if equipped) will be deactivated.

Automatic climate control

For hot weather conditions:

•

The interior cabin will be set to 72°F (22°C).

•

The cooled seats (if equipped and if the feature is selected to AUTO
in the message center) will be set to high.

For cold weather conditions:

•

The interior cabin will be set to 72°F (22°C).

•

The heated seats (if equipped and if the feature is selected to AUTO
in the message center) will be set to high.

•

Rear defrost/heated mirrors (if equipped) will be activated.

For moderate weather conditions:

•

The interior cabin will be heated, cooled, or off, based upon the
previous operating state (last ignition-on cycle).

•

Heated/cooled seats (if equipped) will be deactivated.

•

Rear defrost/heated mirrors (if equipped) will be deactivated.

Climate Controls

80

2012 F-150

(f12)

Owners Guide, 2nd Printing
USA

(fus)

Summary of Contents for 2012 F-150





























































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands