Ford 2012 F-150 Owner'S Manual Download Page 452

Page: 452 / 476

Normal Scheduled Maintenance

At every oil change
interval as indicated
by the message
center

Change engine oil and filter

Rotate tires, inspect tire wear and measure tread
depth

Perform multi-point inspection (recommended)

Inspect automatic transmission fluid level (if
equipped with dipstick); consult dealer for
requirements

Inspect brake pads, shoes, rotors, drums, brake
linings, hoses and parking brake

Inspect cabin air filter (if equipped)

Inspect engine cooling system strength and hoses

Inspect exhaust system and heat shields

Inspect front axle and U-joints; lubricate if
equipped with grease fittings (4WD vehicles)

Inspect half-shaft boots (if equipped)

Inspect steering linkage, ball joints, suspension,
tie-rod ends, driveshaft and U-joints; lubricate if
equipped with grease fittings

Inspect wheels and related components for
abnormal noise, wear, looseness or drag

Reset your Intelligent Oil Life Monitor™ after each engine oil and filter

change; refer to the

Instrument Cluster

chapter

Do not exceed one year or 10,000 miles (16,000 km) between

service intervals

Scheduled Maintenance

452

2012 F-150

(f12)

Owners Guide, 2nd Printing
USA

(fus)

Summary of Contents for 2012 F-150





























































































































































































































































































































































































































































































Search results

Summary of Contents for 2012 F-150

Reviews:

Brands by name

Popular brands

Ford 2012 F-150, Owner'S Manual

Search results

Summary of Contents for 2012 F-150

Reviews:

Brands by name

Popular brands