Ford 2012 F-150 Owner'S Manual Download Page 349

Page: 349 / 476

•

Use commercial car washing equipment

•

Use snow chains on the end of the vehicle with the dissimilar spare
tire/wheel

The usage of a full-size dissimilar spare tire/wheel can lead to
impairment of the following:

•

Handling, stability and braking performance

•

Comfort and noise

•

Ground clearance and parking at curbs

•

Winter weather driving capability

•

Wet weather driving capability

•

All-wheel driving capability (if applicable)

•

Load leveling adjustment (if applicable)

When driving with the full-size dissimilar spare tire/wheel additional
caution should be given to:

•

Towing a trailer

•

Driving vehicles equipped with a camper body

•

Driving vehicles with a load on the cargo rack

Drive cautiously when using a full-size dissimilar spare tire/wheel and
seek service as soon as possible.

Stopping and securing the vehicle

1. Park on a level surface, activate
the hazard flashers and set the
parking brake.

2. Place the gearshift in P (Park)
and turn the engine off.

Roadside Emergencies

349

2012 F-150

(f12)

Owners Guide, 2nd Printing
USA

(fus)

Summary of Contents for 2012 F-150





























































































































































































































































































































































































































































































Search results

Summary of Contents for 2012 F-150

Reviews:

Brands by name

Popular brands

Ford 2012 F-150, Owner'S Manual

Search results

Summary of Contents for 2012 F-150

Reviews:

Brands by name

Popular brands