manualshive.com logo in svg

Ford 2012 F-150, Owner'S Manual

Share
Download
Ford 2012 F-150 Owner'S Manual Download Page 110

Using speed controls

The speed controls are located on the steering wheel. The following
buttons work with speed control:

– SET +:

Press to set a speed or to

increase or decrease the set speed.

CNCL (Cancel)/RSM (Resume):

Press to cancel or resume a set
speed.

ON/OFF:

Press to turn speed

control on or off.

The speed control system uses two

indicator lights in the

instrument cluster:

•

an amber indicator light which illuminates when the system is on, and

•

a green indicator light which illuminates when the system is engaged.

Setting speed control

To set speed control:

1. Press and release ON.

2. Accelerate to the desired speed.

3. Press and release SET +.

4. Take your foot off the accelerator pedal.

5. The green indicator

light on the instrument cluster will turn on.

Note:

•

Vehicle speed may vary momentarily when driving up and down a
steep hill.

•

If the vehicle speed increases above the set speed on a downhill, you
may want to apply the brakes to reduce the speed.

•

If the vehicle speed decreases more than 10 mph (16 km/h) below
your set speed on an uphill, your speed control will disengage.

Disengaging speed control

To disengage speed control, tap the brake pedal or clutch pedal (if
equipped) or press CNCL.

Disengaging the speed control will not erase the previous set speed.

Note:

When you use the clutch pedal to disengage the speed control,

the engine speed may briefly increase, this is normal.

Driver Controls

110

2012 F-150

(f12)

Owners Guide, 2nd Printing
USA

(fus)

Summary of Contents for 2012 F-150





























































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands