manualshive.com logo in svg

Ford 2012 F-150, Owner'S Manual

Share
Download
Ford 2012 F-150 Owner'S Manual Download Page 104

Accessory delay (if equipped)

With accessory delay, the window switches may be used for up to
10 minutes after the ignition switch is turned to the off position or until
any door is opened.

INTERIOR MIRROR

The interior rearview mirror has two pivot points on the support arm
which lets you adjust the mirror up or down and from side to side.

WARNING:

Do not adjust the mirror while the vehicle is in

motion.

Automatic dimming interior rear view mirror (if equipped)

The interior rear view mirror has an auto-dimming function (optional on
the driver’s side exterior mirror). The electronic day/night mirror will
change from the normal (high reflective) state to the non-glare
(darkened) state when bright lights (glare) reach the interior mirror.
When the interior mirror detects bright light from behind the vehicle, the
interior rear view mirror and the driver’s side exterior mirror (if
equipped) will automatically adjust (darken) to minimize glare.

The mirrors will automatically return to the normal state whenever the
vehicle is placed in R (Reverse) to ensure a bright clear view when
backing up.

Do not block the sensors on the front and back of the interior
rear view mirror since this may impair proper mirror
performance.

Note:

A rear center passenger and/or raised rear center headrest (if

equipped) may also block the light from reaching the sensor.

Do not clean the housing or glass of any mirror with harsh
abrasives, fuel or other petroleum-based cleaning products.

Note:

If equipped with a rearview camera system, a video image will

display in the mirror or the navigation system display (if equipped) when
the vehicle is put in R (Reverse). As you shift into any other gear from R
(Reverse), the image will remain for a few seconds and then turn off.
Refer to

Rearview camera system

in the

Driving

chapter.

Driver Controls

104

2012 F-150

(f12)

Owners Guide, 2nd Printing
USA

(fus)

Summary of Contents for 2012 F-150





























































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands